Product ID:PETROTECT VAP-MIL-P-46002,CODE 4085
MSDS Date:01/01/1985
FSC:9150
NIIN:00-985-7293
MSDS Number: BGBWV

Emergency Phone: 412-445-2687

Cage: 6B796

Cage: 6B796

LUBRICATING OIL,PRESERVATIVE,CORROSION INHIBITED.

ACGIH TLV: UNK

Effects of Overexposure:EYES:BURINING &
IRRITATION;SKIN:IRRITATION/DERMATITIS;INHALATION;IRR/DORWSINESS/COM
A;ING:IRR/MON,STO

First Aid:EYES:FLUSH W/LARGE AMT OF WATER.CONTINUE AT LEAST 15 MIN.CALL
DR.SKIN:REMOVE ALL CONT.CLTHG,WASH SKIN W/SOAP & WATER.INHAL:REMOVE
TO FRESH AIR,IF BREATHING HAS STOPPED,APPLY ARTIFICAL RESPIR & GIVE
O* 2,IF RCQD. CALL DR; ING:DO NOT INDUCE VOMTG.

Flash Point:240F
Autoignition Temp:Autoignition Temp Text:>600F

Spill Release Procedures:SCRAPE UP MATERIAL INTO WASTE CONTAINERS,OR
ABSORB WITH DRY SAND OR OIL ABSORBENTS.CLEAN SPILL AREA W/DETERGENT
SOLUTIONS OR SAFETY SOLVENTS.PROVIDE ADEQUATE VENTILATION DURING
CLEAN UP.

Handling and Storage Precautions:STORE IN SEALED CONTAINERS AWAY FROM
HEAT,OPEN FLAME & OXID.MATLS.FIRE EXTINGS.MUST BE KEPT READILY
AVAIL & PERSONNEL TRAINED IN PROPER USE.
Other Precautions:FOR RESPIRATORS DO NOT USE COMPRESSED O*2 IN
HYDROCARBON ATMOSPHERES.DO NOT TRANSFER CONTENTS TO UNMARKED
CONTAINERS.FOLLOW DOT REGS DURING TRANSPORT.NON-HAZ.PROP CHEMICAL
ADDITIVES ADDED PROD

Respiratory Protection:LOW CONC:HALF-MASK OR FULL FACE RESPIR
W/REPL.CARTG.FILTER(SEE SUPPL
Ventilation:ADEQUATE VENTILATION IN ACCORDANCE W/GOOD ENGR PRACTICE
Protective Gloves:SYNTHETIC RUBB
Eye Protection:SPL.PROOF SAFETY GOGGLES
Other Protective Equipment:PLASTIC FACE SHILED,SYN,RUBBER BOOTS,APRONS.
Supplemental Safety and Health
ITEM IS GRADE I OF MIL-P-46002.RESPIRATORY PROTECTION(CONTD):HIGH CONC
MISTS;FULL FACE SUPPLIED AIR RESPIR IN POS PRESS MODE OR FULL FACE
SELF-CONT.BRTHG APPAR W/POS PRESS. NOTE:ALL NIOSH APPD

HCC:V6
Boiling Pt:B.P. Text:400F
Vapor Pres:<1
Vapor Density:>1.0
Spec Gravity:0.90
Evaporation Rate & Reference:<1.0 ETHYL ETHER
Solubility in Water:NEGLIGIBLE
Appearance and Odor:AMBER TRANSPARENT FLUID.PETROLEUM ODOR.
Percent Volatiles by Volume:8.0

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS & CORROSIVE
Hazardous Decomposition Products:NONE

Waste Disposal Methods:WASTE MATERIALS SHOULD BE DUMPED OR BURIED IN AN
APPROVED INDUSTRIAL WASTE LAND FILL.LARGE QUATNITIES MAY BE
DISPOSED OF BY INCINERATION IN A SUITABLE COMBUSTION
CHAMBER.DISPOSAL MUST COMPLY WITH ALL FEDERAL,STATE,& LOCAL
REGULATION.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.